Enail dab kits or enail dab rig bundles are some of the most popular items listed on PuffingBird.com, and we've heard from our customers via phone call and emails saying that the user manual for using these enail kits are not very specific and a bit hard to understand. So on today's Puffing Bird Wiki, we'll be talking about the specific steps for assembling and setting your enail dab kits for the perfect dabbing experience! Please note that this manual is for the desktop enail dab kits made and sold by Puffing Bird, enails from other brands might not be the same in terms of assembling and operating.1. Connecting Your Power Cable To Enail PID Controller. The socket for connecting the power cable is located on the back of the enail PID controller, the power cable features a 3-pin connector(often seen for using on monitor, printers, and PCs) and since this type of power cable is very common and it's very easy to buy and replace. Please note that on this step don't connect the power cable to the power outlet yet. 2. Connecting the Enail Coil To The PID Controller.Simply insert the male joint of the enail coil into the enail PID controller, the side of the small opening window should be facing upward when you insert. The female socket on the controller features a secure mechanism, it will lock the two joints tightly together to prevent the joints from getting lose and falling off. The heating coils listed on PuffingBird.com features two shapes: flat and barrel shape, and many different sizes, from 10mm all the way to 25mm. But the way these enail coils are used is the same, it connects the enail PID controller via the 5-Pin XLR connection.The enail heating coil features a male 5-Pin XLR connection, the temperature sensor is located inside the coil so you can see the temperature index on the screen real-time. After using, you'll need to press the silver "PUSH" button on top of the socket in order to detach the enail coil.3. Putting The Heating Coil On Your Quartz Banger/Titanium Dab Nail. For Quartz BangersThe heating coil for quartz bangers is usually in a barrel shape. First, aline the barrel shape enail coil and the quartz banger, gently put the quartz banger into the coil, make sure that the tail of the coil should be at the bottom so it can rest on the small handle of the banger. For Titanium Dab NailsFirst, screw off the top plate of the titanium nail, then place the coil in the middle of the nail then screw the top plate on again, the tail of the enail coil can be on top or on the bottom, as long as you secure the top plate of the titanium nail both ways are fine. After completing this process, put the quartz banger/titanium dab nail onto any dab rig or bong you've chosen to dab with. The controller will start heating immediately when it's on.4. Turn On The Enail PID Controller. Plug the power cable into your wall socket, then press the ON/OFF switch.The ON/OFF switch is located on the back of the enail PID controller just right next to the power cable socket. Press the silver button then the PID controller will start working. Please note that when the controller is on, it'll resume the temperature setting of your last use, if it's the first time you turn it on, it's default setting is 700 degrees Fahrenheit. 5. Setting The Temperature On The PID Controller. This is the tricky part. First, press the SET button located on the left of the control panel, the index on the screen should start flashing, that means the controller is now in setting mode. The temperature setting will start from the hundreds, press the up and down buttons to select the number you desired and then press the "right" symbol on the right to select the next digit setting. Once you are done with your setting, press SET again, your controller starts working to heat the enail coil to the temperature that you've set. For Low-Temperature Dabs, the temperature should be set from 300~500 degrees Fahrenheit.For High-Temperature Dabs, the temperature should be set from 600 and up. Subjectively speaking, we think that the enail quartz banger is the best for low-temperature dabbing and the titanium dab nails are the best for high-temperature dabbing. 6. After Using. Please note that enail coils can still be very hot after you turn the PID controller off, you'll need to wait at least 15 minutes before touching both the heating coil and the quartz banger/titanium dab nail.Always clean your quartz banger/titanium dab nail after use. If you don't know how to clean your dab nails, here is an article we wrote about clean your quartz bangers, check it out here.Don't clean the heating coil with water! As we mentioned, there is a temperature sensor located in the enail heating coil, you must prevent water from getting into it. Use an alcohol wipe will be the best when it comes to cleaning the heating coils. Further Reading: 5 Best Electric Dab Rig Bundles In 2019What's An Enail Dab Kit? - Dabbing 101Why Is It safer To Use An Enail Dab Kit Instead Of A Butane Torch?